from the XmbTextListToTextProperty(3) man page:
"If insufficient memory is available for the new value string, the functions
return XNoMemory. If the current locale is not supported, the functions return
XLocaleNotSupported. In both of these error cases, the functions do not set
text_prop_return."
Reported by Steffen Nurpmeso <steffen@sdaoden.eu>, thanks!
Ref. https://git.suckless.org/st/commit/2f6e597ed871cff91c627850d03152cae5f45779.html
The bits of uint signal in an XKeyEvent which concern the key group (keyboard
layout) are bits 13 and 14, as documented here:
https://www.x.org/releases/X11R7.7/doc/libX11/XKB/xkblib.html#Groups_and_Shift_Levels
In the older version, only bit 13 was marked as part of XK_SWITCH_MOD, this
causes issues for users who have more than two keymaps. The 14th bit is not
in ignoremod, key sequences are not caught by match(), if they switch to a third
or fourth keyboard.
If the mouse cursor is changed to a bar or an underline then st will use that
when the terminal is first opened. When an application that changes the cursor
via escape sequences is executed, e.g. vim which uses a block cursor by default,
then that cursor will remain after exiting the program.
This change sets the cursor back to default when exiting alt mode.
These are typically mapped in X11 to the side-buttons (backward/forwards) on
the mouse. A comparison of the button numbers in SGR mode (first field):
st old:
0 1 2 64 65 66 67 68 69 70
st new (it is the same as xterm now):
0 1 2 64 65 66 67 128 129 130
A script to test and reproduce it, first argument is "h" (on) or "l" (off):
#!/bin/sh
printf '\x1b[?1000%s\x1b[?1006%s' "$1" "$1"
for n in 1 2 3 4 5 6 7 8 9 10; do
printf 'button %d\n' "$n"
xdotool click "$n"
printf '\n\n'
done
https://git.suckless.org/st/commit/9e68fdbcdb06dfa3d23fe3a7a7f7b59e40e1ea2f.html
st could easily tear/flicker with animation or other unattended
output. This commit eliminates most of the tear/flicker.
Before this commit, the display timing had two "modes":
- Interactively, st was waiting fixed `1000/xfps` ms after forwarding
the kb/mouse event to the application and before drawing.
- Unattended, and specifically with animations, the draw frequency was
throttled to `actionfps`. Animation at a higher rate would throttle
and likely tear, and at lower rates it was tearing big frames
(specifically, when one `read` didn't get a full "frame").
The interactive behavior was decent, but it was impossible to get good
unattended-draw behavior even with carefully chosen configuration.
This commit changes the behavior such that it draws on idle instead of
using fixed latency/frequency. This means that it tries to draw only
when it's very likely that the application has completed its output
(or after some duration without idle), so it mostly succeeds to avoid
tear, flicker, and partial drawing.
The config values minlatency/maxlatency replace xfps/actionfps and
define the range which the algorithm is allowed to wait from the
initial draw-trigger until the actual draw. The range enables the
flexibility to choose when to draw - when least likely to flicker.
It also unifies the interactive and unattended behavior and config
values, which makes the code simpler as well - without sacrificing
latency during interactive use, because typically interactively idle
arrives very quickly, so the wait is typically minlatency.
While it only slighly improves interactive behavior, for animations
and other unattended-drawing it improves greatly, as it effectively
adapts to any [animation] output rate without tearing, throttling,
redundant drawing, or unnecessary delays (sounds impossible, but it
works).
bakkeby
Loic Coyle